HART Loop Converter KFD2-HLC-Ex1.D.4S
- 1-channel isolated barrier
- 24 V DC supply (Power Rail)
- HART field device input (revision 5 to 7) with transmitter power supply
- Usable as signal splitter (1 input and multiple outputs)
- 4 relay outputs (NO)
- 3 analog outputs 4 mA ... 20 mA
- Sink and source mode output
- Configurable by keypad
注: Pepperl+Fuchs GmbH(旧社名)で発行された証明書・適合宣言書などすべての製品関連文書は、Pepperl+Fuchs AG(新社名)にそのまま適用されます。
データシート(PDF):
技術データ KFD2-HLC-Ex1.D.4S
| General specifications | ||
|---|---|---|
| Signal type | Analog input | |
| Supply | ||
| Connection | Power Rail or terminals 23+, 24- | |
| Rated voltage | 19 ... 30 V | |
| Rated current | approx. 140 mA at 24 V DC | |
| Power dissipation | 2.7 W | |
| Power consumption | 3.3 W | |
| HART signal channels (intrinsically safe) | ||
| Conformity | HART field device input (revision 5 to 7) | |
| Input | ||
| Connection | terminals 1, 2, 3, 4, 5, 6 | |
| Input signal | HART communication, transmitter supply | |
| Open circuit voltage/short-circuit current | typ. 24 V / 28 mA | |
| Input resistance | 250 Ω , 5 % (terminals 2, 3 and with jumper on 5, 6) | |
| Available voltage | ≥ 15.5 V at 20 mA, short-circuit protected | |
| Output | ||
| Connection | output I: terminals 10, 11, output II: terminals 11, 12, output III: terminals 16, 17, output IV: terminals 17, 18 output V: terminals 7, 8, 9, output VI: terminals 13, 14, 15, output VII: terminals 19, 20, 21 |
|
| Output I, II, III, IV | ||
| Output signal | relay and LED yellow | |
| Mechanical life | 107 switching cycles | |
| Energized/De-energized delay | approx. 20 ms / approx. 20 ms | |
| Output V, VI, VII | ||
| Output signal | analog | |
| Current range | 4 ... 20 mA , (source or sink mode) | |
| Load | max. 650 Ω , source mode | |
| Voltage range | 5 ... 30 V , sink mode from external supply | |
| Fault signal | downscale I ≤ 2 mA, upscale I ≥ 21.5 mA (acc. NAMUR NE43) or hold measurement value | |
| Other outputs | HART communicator on terminals 22, 24 | |
| Collective error message | Power Rail and LED red | |
| Transfer characteristics | ||
| Output V, VI, VII | ||
| Resolution | max. 2 µA | |
| Accuracy | < 20 µA, 10 µA typ. | |
| Influence of ambient temperature | < ± 2 µA/K | |
| Duration of measurement/Response delay | HART message acquisition time plus 100 ms | |
| Relay | programmable either for fault or trip value (with direction, hysteresis and delay) | |
| Galvanic isolation | ||
| Output I, II/III, IV | functional insulation acc. to IEC 62103, rated insulation voltage 250 Veff | |
| Output I, II, III, IV/other circuits | reinforced insulation acc. to IEC 62103, rated insulation voltage 300 Vrms | |
| Output V/VI/VII/power supply | functional insulation acc. to IEC 62103, rated insulation voltage 50 Veff | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) | |
| Low voltage | ||
| Directive 2014/35/EU | EN 61010-1:2010 | |
| Conformity | ||
| Electromagnetic compatibility | NE 21:2006 | |
| Degree of protection | IEC 60529:2001 | |
| Protection against electrical shock | IEC 60664-1 | |
| Ambient conditions | ||
| Ambient temperature | -20 ... 60 °C (-4 ... 140 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Mass | 300 g | |
| Dimensions | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C2 | |
| Height | 119 mm | |
| Width | 40 mm | |
| Length | 115 mm | |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | BASEEFA 07 ATEX 0174 | |
| Marking |  II (1)GD [Ex ia] IIC, [Ex iaD] |
|
| Input | Ex ia, Ex iaD | |
| Supply | ||
| Maximum safe voltage | 253 V AC (Attention! The rated voltage can be lower.) | |
| Equipment | terminals 1, 4/3 (with link between terminals 4 and 5) | |
| Voltage | 25.2 V | |
| Current | 104.9 mA | |
| Power | 0.661 W | |
| Internal capacitance | 1.1 nF | |
| Internal inductance | 0 mH | |
| Equipment | terminals 2, 5/3 | |
| Voltage | < 28 V | |
| Power | < 1.33 W | |
| Voltage | 1.1 V | |
| Current | 11.9 mA | |
| Power | 4 mW | |
| Internal capacitance | 0 µF | |
| Internal inductance | 0 mH | |
| Output I, II, III, IV | terminals 10, 11; 11, 12; 16, 17; 17, 18 , non-intrinsically safe | |
| Maximum safe voltage | 253 V (Attention! Um is no rated voltage.) | |
| Contact loading | 253 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (BASEEFA 07 ATEX 0174) 50 V AC/1 A/cos φ > 0.7; 30 V DC/1 A resistive load (Pepperl+Fuchs self-declaration) |
|
| Output V, VI, VII | terminals 7, 8, 9; 13, 14, 15; 19, 20, 21 , non-intrinsically safe | |
| Maximum safe voltage | 253 V (Attention! Um is no rated voltage.) | |
| Certificate | PF 07 CERT 1141 X | |
| Marking | II 3G Ex nA nC II T4 X |
|
| Galvanic isolation | ||
| Input/Other circuits | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V | |
| Directive conformity | ||
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 | |
| General information | ||
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210190 |
| ECLASS 12.0 | 27210190 |
| ECLASS 11.0 | 27210190 |
| ECLASS 10.0.1 | 27210190 |
| ECLASS 9.0 | 27210190 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27242692 |
| ETIM 9.0 | EC001601 |
| ETIM 8.0 | EC001601 |
| ETIM 7.0 | EC001601 |
| ETIM 6.0 | EC001601 |
| ETIM 5.0 | EC001597 |
| UNSPSC 12.1 | 39121008 |
Details: KFD2-HLC-Ex1.D.4S
Product Documentation: KFD2-HLC-Ex1.D.4S
| Brief Instructions | 言語 | ファイルタイプ | ファイルサイズ |
|---|---|---|---|
| Operator card KF**-HLC-**1.D* / Bedienkarte KF**-HLC-**1.D* | ALL | 981 KB | |
| Safety and Security Documentation | |||
| Instruction manual | ENG | 50 KB | |
| Manuals | |||
| Manual KF**-HLC-**1.D* | ENG | 4267 KB | |
| Manual | ENG | 3685 KB | |
Design / Simulation: KFD2-HLC-Ex1.D.4S
| CAD | 言語 | ファイルタイプ | ファイルサイズ |
|---|---|---|---|
| CAD 2-D / CAD 2-D | ALL | ZIP | 657 KB |
| CAD 3-D / CAD 3-D | ALL | STP | 870 KB |
| CAE | |||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | ALL | LINK | --- |
| EPLAN macro EDZ / EPLAN Makro EDZ | ALL | EDZ | 88 KB |
Approvals: KFD2-HLC-Ex1.D.4S
| Certificates | 認証番号 | 言語 | ファイルタイプ | ファイルサイズ |
|---|---|---|---|---|
| Baseefa IECEx Certificate of Conformity | IECEx BAS 07.0047 | ALL | LINK | --- |
| Canada FM | FM22CA0014X | ALL | 317 KB | |
| Europe Baseefa ATEX Category (1) G ATEX Category (1) D | Baseefa 07 ATEX 0174 | ALL | 3311 KB | |
| Europe Pepperl+Fuchs Certificate of Compliance ATEX Category 3 G ATEX Category 3 | PF 07 CERT 1141X | ALL | 227 KB | |
| USA FM | CoC 3032427 | ALL | 84 KB | |
| United Kingdom UK-Type Examination Certificate UKEX Category (1) G UKEX Category (1) D | CML 21UKEX21103 | ALL | 198 KB | |
| Control Drawings | ||||
| Control drawing FM / Control drawing FM | ALL | 58 KB | ||
Software: KFD2-HLC-Ex1.D.4S
| Frameworks | Release Info | ファイルタイプ | ファイルサイズ |
|---|---|---|---|
| PACTware 4.1 SP6 / PACTware 4.1 SP6 | 4.1.0.53 | ZIP | 43327 KB |
| Device Description Files/Drivers | |||
| DTM Collection HART Loop Converter / DTM Collection HART Loop Converter | 1.0.6.0 | ZIP | 13857 KB |
株式会社 ピーアンドエフ
〒220-0022
神奈川県横浜市西区花咲町6-145
横浜花咲ビル5F 日本
日本
sales@jp.pepperl-fuchs.com
+81 45 6249077
株式会社ピーアンドエフ
大阪府豊中市新千里東町1-5-3
千里朝日阪急ビル15階
〒560-0082 大阪
日本
sales@jp.pepperl-fuchs.com
+81 6 6836-5620
© 2024 All Rights Reserved.
Pepperl+Fuchsはグローバルオートメーション市場向けにセンサや部品の開発を行っており、革新的かつ高品質な技術躍進のために日々努力を続けています。ドイツ・アメリカ・シンガポール・ハンガリー・インドネシア・ベトナムに生産拠点があり、すべての工場でISO9001認証を取得しています。