Rotation Speed Monitor EG2-M2-DW
- 2-channel isolated barrier
- 24 V DC supply
- Dry contact or NAMUR inputs
- Input frequency adjustable
- 2 relay outputs
- 2 serially switched outputs
- Start-up override
- Min/Max monitoring possible in 1-channel operation
注: Pepperl+Fuchs GmbH(旧社名)で発行された証明書・適合宣言書などすべての製品関連文書は、Pepperl+Fuchs AG(新社名)にそのまま適用されます。
データシート(PDF):
技術データ EG2-M2-DW
| General specifications | ||
|---|---|---|
| Signal type | Digital Input | |
| Supply | ||
| Connection | d14+, z14- | |
| Rated voltage | 20.4 ... 27.6 V DC | |
| Ripple | ≤ 10 % | |
| Rated current | approx. 130 mA | |
| Input | ||
| Input (intrinsically safe) | ||
| Connection | channel 1: d2+, d4- channel 2: z2+, z4- |
|
| Rated values | acc. to EN 60947-5-6 (NAMUR), see manual for electrical data | |
| Open circuit voltage/short-circuit current | approx. 8 V DC / approx. 8 mA | |
| Switching point/switching hysteresis | 1.2 ... 2.1 mA / approx. 0.2 mA | |
| Pulse/Pause ratio | ≥ 0.5 ms / ≥ 0.5 ms | |
| Input (non-intrinsically safe) | ||
| Connection | start-up override: channel 1: d16, channel 2: z16 mode of operation output relay: channel 1: b16, channel 2: b18 |
|
| Input current | 1 mA | |
| Signal level | 1-signal: 15 ... 30 V DC 0-signal: 0 ... 5 V DC |
|
| Input delay | 5 ... 20 ms | |
| Output | ||
| Connection | channel 1: output I: d30, d28, d32, output II: d24, d22, d26, output III: d18, output IV: d20 channel 2: output V: z30, z28, z32, output VI: z24, z22, z26, output VII: z18, output VIII: z20 |
|
| Switching current | max. 10 mA , short-circuit protected (outputs III, IV, VII, VIII) | |
| Output | signal ; relay (outputs I, II, V, VI) electronic output, active (outputs III, IV, VII, VIII) |
|
| Signal level | 0-signal/1-signal: 19 V DC switched off (off-state current ≤ 10 µA) (outputs III, IV, VII, VIII) | |
| Contact loading | 50 V AC/2 A/cos φ = 1/1 A/cos φ = 0.3; 70 V DC/100 W resistive load (outputs I, II, V, VI) | |
| Energized/De-energized delay | approx. 10 ms / approx. 5 ms (outputs I, II, V, VI) | |
| Mechanical life | 2 x 105 switching cycles (outputs I, II, V, VI) | |
| Transfer characteristics | ||
| Measurement range | 0.001 ... 99 Hz | |
| Switching frequency | ≤ 1 kHz | |
| Switching hysteresis | approx. 1 % of adjusted trip point | |
| Switching point error | ≤ 1 % of adjusted trip point | |
| Repeat accuracy | ≤ 1 % of adjusted trip point | |
| Galvanic isolation | ||
| Input/Output | available | |
| Input/power supply | available | |
| Output/power supply | available | |
| Directive conformity | ||
| Electromagnetic compatibility | ||
| Directive 2004/108/EC | The device has been used for the same applications for several years. It therefore features an appropriate electromagnetic field immunity. The device must not be used in new plants. | |
| Conformity | ||
| Degree of protection | IEC 60529 | |
| Ambient conditions | ||
| Ambient temperature | 0 ... 60 °C (32 ... 140 °F) | |
| Mechanical specifications | ||
| Degree of protection | IP20 | |
| Connection | 48-pin plug connector acc. to DIN 41612 , series 2 , type F , z, b and d provided | |
| Mass | approx. 300 g | |
| Dimensions | 20 x 128 x 193 mm (0.8 x 5 x 7.5 inch) | |
| Height | 128 mm | |
| Width | 20 mm | |
| Length | 190 mm | |
| Construction type | Eurocard 100 x 160 mm (3.9 x 6.3 inch) acc. to DIN 41494, front panel 4TE, mountable in 19 inch rack | |
| Coding | a3/c3 | |
| Data for application in connection with hazardous areas | ||
| EU-type examination certificate | PTB 00 ATEX 2210 , for additional certificates see www.pepperl-fuchs.com | |
| Marking |  II (1)GD [EEx ia] IIC |
|
| Input | EEx ia IIC | |
| Voltage | 12.7 V | |
| Current | 20 mA | |
| Power | 62 mW (linear characteristic) | |
| Supply | ||
| Maximum safe voltage | 40 V (Attention! The rated voltage can be lower.) | |
| Directive conformity | ||
| Directive 94/9/EC | EN 50014:1997, EN 50020:1994 | |
| General information | ||
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27210128 |
| ECLASS 12.0 | 27210128 |
| ECLASS 11.0 | 27210128 |
| ECLASS 10.0.1 | 27210128 |
| ECLASS 9.0 | 27210128 |
| ECLASS 8.0 | 27210190 |
| ECLASS 5.1 | 27210121 |
| ETIM 9.0 | EC002918 |
| ETIM 8.0 | EC002918 |
| ETIM 7.0 | EC002918 |
| ETIM 6.0 | EC002918 |
| ETIM 5.0 | EC002475 |
| UNSPSC 12.1 | 39121007 |
Details: EG2-M2-DW
Product Documentation: EG2-M2-DW
| Manuals | 言語 | ファイルタイプ | ファイルサイズ |
|---|---|---|---|
| Brief Instructions - E-system | ENG | 320 KB |
株式会社 ピーアンドエフ
〒220-0022
神奈川県横浜市西区花咲町6-145
横浜花咲ビル5F 日本
日本
sales@jp.pepperl-fuchs.com
+81 45 6249077
株式会社ピーアンドエフ
大阪府豊中市新千里東町1-5-3
千里朝日阪急ビル15階
〒560-0082 大阪
日本
sales@jp.pepperl-fuchs.com
+81 6 6836-5620
© 2024 All Rights Reserved.
Pepperl+Fuchsはグローバルオートメーション市場向けにセンサや部品の開発を行っており、革新的かつ高品質な技術躍進のために日々努力を続けています。ドイツ・アメリカ・シンガポール・ハンガリー・インドネシア・ベトナムに生産拠点があり、すべての工場でISO9001認証を取得しています。